9. Troubleshooting

9.1. Troubleshooting case creation

Generally, create_newcase errors are reported to the terminal and should provide some guidance about what caused them.

If create_newcase fails on a relatively generic error, first check to make sure the command-line arguments match the interface’s specification. See the help text to review usage.

> create_newcase --help

9.2. Troubleshooting job submission

Most problems associated with submission or launch are site-specific. The batch and run aspects of the case.submit script are created by parsing the variables in $CASEROOT/env_batch.xml file.

Take these steps to check for problems:

  1. Review the batch submission options in $CASEROOT/env_batch.xml. Confirm that they are consistent with the site-specific batch environment, and that the queue names, time limits, and hardware processor request make sense and are consistent with the case.

  2. Make sure that case.submit uses the correct batch job tool for submitting the case.submit script. Depending on the batch environment, it might be bsub, qsub or another command. Also confirm if a redirection “<” character is required. The information for how case.submit submits jobs appears at the end of the standard output stream.

9.3. Troubleshooting runtime problems

To see if a run completed successfully, check the last several lines of the cpl.log file for a string like SUCCESSFUL TERMINATION. A successful job also usually copies the log files to the $CASEROOT/logs directory.

Check these things first when a job fails:

  • Did the model time out?

  • Was a disk quota limit hit?

  • Did a machine go down?

  • Did a file system become full?

If any of those things happened, take appropriate corrective action (see suggestions below) and resubmit the job.

If it is not clear that any of the above caused a case to fail, there are several places to look for error messages.

  • Check component log files in your run directory ($RUNDIR). This directory is set in the env_run.xml file. Each component writes its own log file, and there should be log files for every component in this format: cpl.log.yymmdd-hhmmss. Check each log file for an error message, especially at or near the end.

  • Check for a standard out and/or standard error file in $CASEROOT. The standard out/err file often captures a significant amount of extra model output and also often contains significant system output when a job terminates. Useful error messages sometimes are found well above the bottom of a large standard out/err file. Backtrack from the bottom in search of an error message.

  • Check for core files in your run directory and review them using an appropriate tool.

  • Check any automated email from the job about why a job failed. Some sites’ batch schedulers send these.

  • Check the archive directory: $DOUT_S_ROOT/$CASE. If a case failed, the log files or data may still have been archived.

Common errors

One common error is for a job to time out, which often produces minimal error messages. Review the daily model date stamps in the cpl.log file and the timestamps of files in your run directory to deduce the start and stop time of a run. If the model was running fine, but the wallclock limit was reached, either reduce the run length or increase the wallclock setting.

If the model hangs and then times out, that usually indicates an MPI or file system problem or possibly a model problem. If you suspect an intermittent system problem, try resubmitting the job. Also send a help request to local site consultants to provide them with feedback about system problems and to get help.

Another error that can cause a timeout is a slow or intermittently slow node. The cpl.log file normally outputs the time used for every model simulation day. To review that data, grep the cpl.log file for the string tStamp as shown here:

> grep tStamp cpl.log.* | more

The output looks like this:

tStamp_write: model date = 10120 0 wall clock = 2009-09-28 09:10:46 avg dt = 58.58 dt = 58.18
tStamp_write: model date = 10121 0 wall clock = 2009-09-28 09:12:32 avg dt = 60.10 dt = 105.90

Review the run times at the end of each line for each model day. The “avg dt =” is the average time to simulate a model day and “dt = ” is the time needed to simulate the latest model day.

The model date is printed in YYYYMMDD format and the wallclock is the local date and time. In the example, 10120 is Jan 20, 0001, and the model took 58 seconds to run that day. The next day, Jan 21, took 105.90 seconds.

A wide variation in the simulation time for typical mid-month model days suggests a system problem. However, there are variations in the cost of the model over time. For instance, on the last day of every simulated month, the model typically writes netcdf files, which can be a significant intermittent cost. Also, some model configurations read data mid-month or run physics intermittently at a timestep longer than one day. In those cases, some variability is expected. The time variation typically is quite erratic and unpredictable if the problem is system performance variability.

Sometimes when a job times out or overflows disk space, the restart files will get mangled. With the exception of the CAM and CLM history files, all the restart files have consistent sizes.

Compare the restart files against the sizes of a previous restart. If they don’t match, remove them and move the previous restart into place before resubmitting the job. See Restarting a run.

It is not uncommon for nodes to fail on HPC systems or for access to large file systems to hang. Before you file a bug report, make sure a case fails consistently in the same place.